Type 1+2 AC surge protector - 1-pole
DS250VG-300/DE
Part Number: 3300
- Type 1+2+3 unipolar surge protector
- 25 kA on 10/350µs impulse
- Low voltage Up
- Internal disconnection, status indicator and remote signaling
- Optimized to TOV
- IEC 61643-11 compliance
- UL1449 ed.4 recognition
Installation Sheet
Installation Sheet
The DS250VG is an extreme duty Type 1+2+3 AC surge protector device designed to protect at the entrance of the electrical installation. This SPD is particularly useful in a high lightning density area where the risk of heavy surge current or even direct strike is high (eg: buildings equipped with lightning rods). The DS250VG is one-pole SPD and can be used in common mode or common and differential mode.
DS250VG AC surge protectors are designed to be connected in multi-pole configuration to protect single-phase, 3-phase and 3-phase+Neutral AC networks, sometimes associated with a dedicated N/PE SPD.
Select another reference:
| SPD type following IEC test |
1+2+3 |
| Network |
230/400 V |
| Nominal line voltage |
230 Vac |
| Max. AC operating voltage L-N |
255 Vac |
| Max. load current |
100 A |
| Temporary Over Voltage (TOV) Charasteristics - 5 sec. without disconnection |
335 Vac withstand |
| Temporary Over Voltage (TOV) Charasteristics - 120 mn without disconnection or with safety disconnection |
440 Vac withstand |
| Residual Current Leakage current to Ground |
None |
| Operating current Continious current at Uc |
None |
| Follow current |
None |
| Nominal discharge current 15 x 8/20 µs impulses |
30 kA |
| Max. discharge current max. withstand @ 8/20 µs by pole |
70 kA |
| Impulse current by pole max. withstand 10/350µs by pole |
25 kA |
| Withstand on Combinaison waveform IEC 61643-11 Class III test: 1.2/50µs - 8/20µs |
20 kV |
| Withstand on overvoltages IEEE C62.41.1 |
20 kV |
| Admissible short-circuit current |
50000 A |
| Connection mode(s) |
L/N or L/PE |
| Protection mode(s) |
Common Mode or Differential Mode |
| Protection level @ In (8/20µs) |
1.5 kV |
| Residual voltage @ In (8/20 µs) |
1.1 kV |
| Protection level L/PE @ In (8/20µs) |
1.5 kV |
| Specific energy by pole max. withstand 10/350 µs |
156 kJ/ohm |
| Technology | VG |
| SPD configuration | 1-pole |
| Connection to Network | By screw terminals : 6-35 mm² / by bus |
| Format |
1-pole modular box |
| Mounting |
Symmetrical rail 35 mm (EN60715) |
| Housing material | Thermoplastic UL94-V0 |
| Operating temperature | -40/+85°C |
| Protection rating | IP20 |
| Failsafe behavior | Disconnection |
| Disconnection indicator | 1 mechanical indicator |
| Remote signaling of disconnection |
Output on changeover contact |
| Dimensions |
See diagram |
| Standards compliance |
IEC 61643-11 / EN 61643-11 / UL1449 4ed. |
| Certification |
UL / CSA / EAC |
| Thermal disconnector | Internal |
| Installation ground fault breaker | Type 'S' or delayed |
| Fuses |
Fuses type gG - 315 A |
